REV Robotics

Models inREV Robotics CatalogElectronics
Results 1-10 of 26
< Previous Page123Next Page >
Results per page:
Part Number
Supplier
Description
The REV Robotics Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will trigger the sensor.
Category
Tags
Configurations?
No
Downloads
1
Added on
24 Dec, 2019
Part Number
Supplier
Description
This 10K potentiometer can be used as an analog sensor with the Expansion Hub. This potentiometer has a 270 degree range of motion and can be mounted to any REV Robotics brackets with the Motion Interface Pattern, like the Motion Bracket. The input shaft is a 5mm hex socket so it can be mounted to end of any of the REV 5mm Hex Shafts to give sensor feedback on simple arm joint.
Category
Tags
Configurations?
No
Downloads
0
Added on
24 Dec, 2019
Part Number
Supplier
Description
Touch sensor is best used for user input, but can also be used as a limit switch
Category
Tags
Configurations?
No
Downloads
1
Added on
24 Dec, 2019
Part Number
Supplier
Description
The REV Robotics 2m Distance Sensor uses the ST Microelectronics VL53L0X Time-of-Flight (ToF) laser-ranging module to measure distances up to 2 meters with millimeter resolution. Unlike other ranging sensors that rely on the intensity of reflected light, this sensor can measure how long it takes for the light to bounce back, the "time of flight." This results in much more accurate measurements that are independent of the target's reflectance.
Category
Tags
Configurations?
No
Downloads
0
Added on
24 Dec, 2019
Part Number
Supplier
Description
This sensor can be used to read and compare colors, and also has a built-in IR (optical) Proximity Sensor and white LED for active target lighting. Supports High Speed I2C Communication (400kHz) as well as auto increment register read which allows the user to return all the color register and status register data in one read command instead of 4 separate read commands
Category
Tags
Configurations?
No
Downloads
1
Added on
24 Dec, 2019
Part Number
Supplier
Description
Add this switch between your battery and Expansion Hub to have convenient on/off control of your robot. We recommend mounting the switch slightly recessed from the outside of your robot so that it's not accidentally turned off by another robot during a match.
Category
Tags
Configurations?
No
Downloads
0
Added on
24 Dec, 2019
Part Number
Supplier
Description
This 10-cell, 12V 3000mAh battery has a low profile configuration to make it easier to mount on a robot. The Slim Battery pack is wired with an XT30 male connector and an inline 20A replaceable ATM fuse.
Category
Tags
Configurations?
No
Downloads
8
Added on
24 Dec, 2019
Supplier
Description
The UltraUSB Hub is designed specifically for use in competitive robotics, and gives you the ability to connect multiple USB devices to each other as well as replacing cables when damaged instead of needing to replace the whole hub.
Category
Tags
Configurations?
No
Downloads
0
Added on
24 Dec, 2019
Supplier
Description
This is a 3D printable part for mounting the Logitech C270 UVC USB Camera to the REV 15mm Build System
Category
Tags
Configurations?
No
Downloads
0
Added on
24 Dec, 2019
Supplier
Description
This is a 3D printable part for mounting the Logitech C270 UVC USB Camera to the REV 15mm Build System
Category
Tags
Configurations?
No
Downloads
0
Added on
24 Dec, 2019
Category Tags

About

Robotics parts supplier dedicated to helping promote STEAM globally. Proud supplier of FIRST Global, FIRST Tech Challenge, and FIRST Robotics Competition.

Contact Details

Address:
1621 W Crosby Rd
Suite 104
Carrollton, 75006
Texas, United States
Phone: 8442552267
Email:
Website: www.revrobotics.com